Click on photo for larger view JACK, 1/4', MONO PC MOUNT PLASTIC, GENUINE CLIFF 4 PC board terminals, switched. Used in many brands of amps and other equipment. With nut and washer. Original Cliff UK part number CL1169. Part #J-503 $1.99 Click on photo for larger view SAVE WITH MULTIPACK! JACK, 1/4', MONO PC MOUNT PLASTIC, GENUINE CLIFF UK, PACK OF 6 4 PC board terminals, switched. Used in many brands of amps and other equipment.

Pack of 6 jacks, with nuts and washers. Original Cliff UK part number CL1169. Part #J-503-6 $9.99 (Set of 6 jacks) Click on photo for larger view JACK, 1/4', MONO PC MOUNT PLASTIC, GENUINE CLIFF UK, RED NUT, REPLACEMENT FOR Marshall® SPEAKER JACKS. 4 PC board terminals, switched. Used in modern Marshall® TM amp heads (JCM2000 series TSL and DSL, for example) as the output jack for the speaker cabinet. With red nut and washer. Part #J-503R $2.39 Click on photo for larger view Note: Nut & Washer NOT included - reuse original, or order JN-916 JACK, 9-PIN Low Profile, 1/4', Marshall®, Fender®.

DSL 100 & DSL 50 V alve Heads JCM 2000. JCM 2000 Introduction The Marshall 1959 Super Lead Plexi head and the JCM 800 Master Volume 2203.

Used as the Effects A return jack and Effects B return jack on the rear panel of the Marshall® DSL-50, DSL-100 and TSL-100. Replaces Marshall part number J3D86074. Nut and washer are NOT included. Chrome trim ring. NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW Part #J-560 $2.95 Click on photo for larger view Note: Nut & Washer NOT included - reuse original, or order JN-916. JACK, 1/4', Marshall® TSL100, 4-PIN.

Used as the Effects A and Effects B send jack on the rear panel of the DSL-50, DSL-100 and TSL-100. Also used as the input jack on the Marshall® MS-4 Micro Stack. Note: The original jack on these Marshalls had 5 pins - this replacement has 4 pins. The pin that is missing on this replacement jack has no function in the circuitry. Replaces original Marshall® part number J3D86075 NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW Part #J-6075 $5.95 Click on photo for larger view JACK NUT, PLASTIC, GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.

Replacement jack nut as found on the J-503, J-504 jacks. Part #J-5NT $0.50 Click on photo for larger view JACK NUT MULTI-PACK - SAVE! 6 JACK NUTS, PLASTIC, GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.

Replacement jack nut as found on the J-503, J-504 jacks Part #J-5NT-6 $2.39 Click on photo for larger view JACK NUT, PLASTIC, GENUINE CLIFF UK, RED Replacement nut for the J-503, J-504. Red nuts on these jacks typically are used on later model Marshall® amps to designate the 'speaker' jacks. Part #J-5NTR $0.60 NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE. Fits J-506, J-506A, J-507, J-530, J-531, J-532, J-532G, J-533, J-533G, J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560.

Part #JN-916 $0.79 SAVE WITH MULTIPACK! NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE, SET OF 6. Fits J-506, J-507, J-530, J-531, J-532, J-532G,J-533, J-533G, J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560. Set of 6 JN-916 nuts with washers Part #JN-916-6 $3.59 (For set of 6 nuts and 6 washers) Click on photo for larger view POT, 11mm, Marshall® TYPE, PC MOUNT. This pot has 4 pins.

Includes mounting nut. POT VALUE MARSHALL PART NUMBER APPLICATION B5K POT7 PRESENCE VR10 B20K POT2 REVERB A VR5, REVERB B VR6, MIDDLE VR8 B200K POT5 TREBLE VR9 A1M POT6 CHANNEL A CLASSIC GAIN VR1, CHANNEL A CLASSIC VOLUME VR2, CHANNEL B ULTRA GAIN VR3, CHANNEL B ULTRA VOLUME 1 VR 4, BASS VR7 Select Pot Value in Options Part #P-VKG-XX $6.95 Select Option: Quantity: Click on photo for larger view Complete Marshall® POT KIT, 10 POTS TOTAL. ORIGINAL Marshall® REPLACEMENT PARTS. Marshall® MODEL DSL50 in the JCM2000 SERIES.

Complete replacement pot kit for the Marshall® Model DSL50 in the JCM2000 amp series. 10 pots on the front panel. Part #MPK-26 $56.95 Click on photo for larger view KNOB, Marshall®, PUSH ON D-SHAFT (Read applicable models!) Standard original Marshall® control knob, push-on type, for D-Shaft pots used in the following Marshall® amp models: DSL-50 Head Original Marshall® part. Part #MKDS $2.99 (Single Knob) Click on photo for larger view Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END. Common replacement cord for many guitar amps, power amps, effects units, etc.

Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-300 $5.95 Click on photo for larger view Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.

Replacement cord for many guitar amps, power amps, effects units, etc. 10 ft length giveS extra flexibility in equipment placement, reduces use of extension cords. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. IEC connector at equipment end. Used only in North America. Part #PC-600 $10.95 Click on photo for larger view IEC POWER CONNECTOR, NON-FUSED, WIRED TYPE, SCREW ATTACHMENT TO PANEL Popular IEC type AC connector found in many amplifiers and effects units. Designed to mount in 0.8' x 1.10' rectangular panel hole.

Screw holes are 1.57' apart, center-to-center. Connectors are for 1/4' push on terminals, or may be soldered. Rated at 10 amps. Part #P-S2-10 6 $2.95 Click on photo for larger view ROCKER SWITCH, LIGHTED POWER, ORIGINAL Marshall®, FOUND IN Marshall® JVM and JCM2000 SERIES Used in the TSL100, TSL122, DSL100, DSL50. Has 4 electrical terminals on back of switch. 1/4' push-on terminals. Rated 22A @ 125VAC.

15/16' x 1 1/16' x 1' deep. Internal neon lamp powered by 120VAC.

Not for use on 230VAC. Original Marshall part number B8C75184. Part #SW-493 $8.95 Click on photo for larger view Marshall® Impedance/Mode Selector switch.

Correct replacement for PCB mount impedance and high-low (pentode- triode) mode switch found on the back of many Marshall® JCM900 and JCM2000 series amplifiers. Also used as the impedance switch in Marshall® 4x12 Cabinets (such as the 1960 series cabinets). Found in other British-made amplifiers and cabinets as well. Marshall® part number S208. Part #SW- 4500 $7.95 Click on photo for larger view ORIGINAL REPLACEMENT CAP FOR FH-815 FUSE HOLDERS - Marshall® Cap for the 'HT' fuse holder only in the JCM2000 series (TSL100, TSL122, DSL100, DSL50). The Mains fuse holder in the TSL and DSL models uses the FH-816 cap (below).

Part #FH-204 $2.95 Click on photo for larger view ORIGINAL REPLACEMENT CAP FOR FH-810 FUSE HOLDER - Marshall® Cap for the 'Mains' fuse holder found on the Marshall® JCM2000 series (TSL100, TSL122, DSL100, DSL50). The HT fuse holder in the TSL and DSL models uses the FH-204 cap (above). Common failure item in Marshall®. Designed to work with AGC type fuses (1/4' x 1 1/4') If you would like to switch your TSL or DSL Mains Fuse to a GMA fuse (5mm x 20mm), order the FH-815 fuse cap below. Part #FH-816 $2.95 Click on photo for larger view ORIGINAL REPLACEMENT FUSE CAP KIT Marshall® TSL100, TSL122, DSL100, DSL50 This kit contains the large fuse cap for the 'Mains' fuse holder and the small fuse cap for the HT fuse holder found on the Marshall® TSL100, TSL122, DSL100, DSL50. Part #FH-416 $4.95 (for a set of two fuse caps) Click on photo for larger view ALTERNATE CAP FOR FH-810 FUSE HOLDER - Marshall® - FOR GMA STYLE FUSE Cap for the 'Mains' fuse holder found on the Marshall® JCM2000 series (TSL100, TSL122, DSL100, DSL50). NOTE: This cap is NOT the original cap - this cap will change the type of fuse used in in the Mains fuse holder from the original AGC type to the GMA type (GMA is the same physical size (5mm x 20mm) as used in the HT fuse holder).

Part #FH-815 $2.95 Click on photo for larger view ORIGINAL REPLACEMENT FUSE HOLDER - Marshall® Replacement for mains and HT fuse holders found on the Marshall® JCM900 series. Replacement fuse holder for the HT fuse only in the larger TSL and DSL models in the JCM2000 series (TSL100, TSL122, DSL100, DSL50). Includes the FH-204 cap (above). Common failure item in Marshall®. Designed to work with GMA type fuses (5mm x 20mm) Part #FH-830 $5.95 Click on photo for larger view ORIGINAL REPLACEMENT FUSE HOLDER - Marshall® Replacement fuse holder for the Mains fuse only in the JCM2000 TSL and DSL models (TSL100, TSL122, DSL100, DSL50). Includes the FH-816 cap (above).

Common failure item in Marshall®. Web Service To File Scenario In Sap Pi Developer. Designed to work with AGC type fuses (1/4' x 1 1/4').

May be converted to GMA fuses with the FH-815 cap. Part #FH-810 $5.95 Click on photo for larger view OCTAL TUBE KEYWAY, SET OF 2 If you have a cherished octal power tube or rectifier with a broken keyway, here is a great solution. By cleaning the remainder of the broken keyway from the tube base and properly installing this keyway replacement (a little dab of silicone sealant works great to hold it in place), your tube can safely be reinstalled into your equipment. These great tube-savers are sold in sets of 2. Note: when using an adhesive to secure the keyway to the tube base, DO NOT use a water-based glue.

Silicone sealant (RTV) which is acryllic-based or butyl-based is fine. Latex sealant or hot-glue is NOT.

Part #OTK8-2 $5.99 (for a set of 2 tube keyways) Click on photo for larger view 9 pin Belton micalex socket for PC board mouting, 3/4' PC hole, 1 1/8' mounting centers. Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.

Used in Marshall®, Peavey® and other brands where the tube socket is mounted to a PC board. For additional specs. Part #TS-9-BEL $2.79 Click on photo for larger view Socket - Belton, Micalex, 8 Pin, Octal PC Mount, Long Lead Micalex, PC mount, long leads (Belton) - MB/MT. 1 ½' mounting centers 1 ¼' chassis hole. Applicable for use with all types of electric and electronic equipment using vacuum tubes. Paddle saddle mounting, easy mount with the saddle of extruded screw hole.

Phosphorous bronze pin terminal with tin plating, glass fiber field PPS Insulating material Part # TS-8-209 $3.50 Click on photo for larger view TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34. Used in Marshall® and many other amps. 1 1/2' mounting centers. Made by Belton. Part #TC-142 $1.95 (TUBE NOT INCLUDED) Click on photo for larger view Revisit™ PRE-AMP TUBE DAMPER RINGS.

Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics. An economical alternative to more expensive tube dampers. Will withstand high temperatures of pre-amp tubes, reusable when you change tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Part #PTD-6 $2.99 (Set of 6 rings) Click on photo for larger view Marshall® DSL50 Main Circuit Board This is the replacement main PC board for the Marshall® DSL50. Does not fit any other Marshall® model.

Replacing this board fixes the common problem of drifting bias on the power tubes in these amplifiers. Original Marshall®, made in England, Marshall® part number DL50-60-00 Note: Included with this board we provide installation guidelines and the schematic of the PC board.

We recommend only experienced amplifier technicians attempt replacing this board. Part #PCB-117 $245.95 SPECIAL ORDER Lead time is currently 3-4 weeks SPECIAL ORDER Lead time is currently 3-4 weeks Diode, Silicon Rectifier, 1A, 1000PIV Part #1N4007 $0.12 Diode, Silicon Signal, 150mA, 100PIV Part #1N4148 $0.12 Diode, Silicon Rectifier, 3A, 1000PIV Part #1N5408 $0.60 Bridge, Silicon Rectifier, 8A, 1000PIV Upgrade for original part KBPC602, which tends to overheat and shut down, causing loss of preamp filaments. Part #KBPC810 $2.95 Op-Amp, 4558, very common in amplifiers, mixers, power amps. 8-pin DIP Part #NJM4558-D $1.00 Low-noise, JFET input, TL071 Single Op-Amp in 8-pin DIP package.

Also TL071CN. Part #TL071CP $1.50 OP AMP, SWITCHABLE, USED IN CERTAIN Marshall® AMPS, INCLUDING THE JCM2000 (TSL & DSL) SERIES. MAY BE LABELED AS M2120 OR M5201.

Part #NJM2120D $2.95 Click on photo for larger view Revisit™ Reverb Tank, 17' long, 2 spring, equivalent to Accutronics 4BB3C1D. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded. Mounts on vertical wall, long axis horizontal, connectors down. Common replacement for Marshall® DSL50. Also found in certain Laney® models.

See explanation of Accutronics reverb tank numbering system. See a chart which lists AC impedance and DC resistance measurements for reverb tanks. Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet. View the 3-year warranty details.

Part #4BB3C1D 'Bringing back the sound of vintage Accutronics tanks' $29.99 In Stock Click on photo for larger view Rubber mounting grommets for reverb tanks, package of four. Provides shock absorption for tanks mounted directly to the inside of a wooden amp cabinet. Mounting Hole Diameter = 3/8' Outer Diameter = 1/2' Part #RRG-4 $1.99 (For a pack of 4 grommets - In Stock) Click on photo for larger view 4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices. Dual cable, excellent shielding properties, 4 feet long. Part #RC-174 $4.95 In stock Click on photo for larger view Marshall® STYLE FOOTSWITCH W/LED Revisit™ aftermarket replacement for the original Marshall® footswitch - same quality, just without the Marshall® logo and Marshall® price tag. Sturdy metal construction.

Replaces Marshall® stock numbers PED801 and PEDL-00001. Fits the Marshall® DSL50. Mono 1/4' Plug, 16 ft. LED indicates condition of switch. Part #FBS-470L $21.95 Click on photo for larger view Marshall® CORNERS, COMPLETE SET Front and rear corner set, ¾' radius. Includes 4 front corners, 4 rear corners, and 28 gold rivets for attaching corners to cabinet. For heads, combos and straight speaker cabinets.

Will not fit slanted speaker cabinets, such as the 1960A. Part # MC-109 $17.95 (For a set of 8 corners with 28 rivets) Click on photo for larger view Marshall® CORNERS, FRONT OF CABINET Front corner set, ¾' radius. Includes 12 gold rivets for attaching to cabinet. For heads, combos and straight speaker cabinets. Will not fit slanted speaker cabinets, such as the 1960A. Part # MC-1091 $9.95 (For a set of 4 corners with 12 rivets) Click on photo for larger view Marshall® CORNERS, REAR OF CABINET Rear corner set, ¾' radius.

Includes 16 gold rivets for attaching to cabinet. For heads, combos and speaker cabinets. Part # MC-1090 $9.95 (For a set of 4 corners with 16 rivets) Click on photo for larger view Marshall® RIVETS For attaching Marshall® corners to cabinets. Gold, package of 12 rivets. Part # MR-109 $4.95 (For a set of 12 gold rivets) Click on photo for larger view MARSHALL® SPRUNG FOOT FOR TSL100 HEAD. Original Marshall® Sprung foot. Sold individually.

Screws are included 3 1/4' Long, 2' Wide, 1' Tall. 2-5/16' Mounting Centers. Part #MSF-252 $8.95 (each) Click on photos for larger view (Assembled) Marshall® HANDLE Genuine Marshall® Handle for modern heads and combo amps. Used primarily on JCM900, JCM2000, larger ValveState, and JVM series amps, along with some later JCM800. Original Marshall® part number M-PACK-00031. Kit contains: • (2) Countersunk screws - M5 x 0.8, overall length of 25 mm • (2) Mounting brackets • (2) Black bracket covers with Marshall® logo • (1) Rubber handle with metallic insert • Center-to-center screw mounting distance is 8 3/8' (213mm). • Overall length of assembled and mounted handle is 10¼' (260mm).

• Replacement screws are the Marshall® SC-404 screws, below Part #MAH-294 $16.99 Click on photo for larger view Marshall® METRIC HANDLE SCREWS Pack of 2 metric handle screws for Marshall® MAH-294 handle. Original Marshall®, designed to work with the OEM metric T-Nuts.

Set of 2 Flat-head counter-sunk Phillips, M5 x 0.8, length 25 mm. Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps, along with some later JCM800.

Part #SC-404 $1.99 (for a pack of 2 Marshall® metric screws) Click on photo for larger view Marshall® LOGO, WHITE PLASTIC, 11' LONG - TSL100 The 11 inch long Marshall® logo - large size. As used on the DSL50 head. This logo is 11' long - please measure the old logo in order to ensure that you order the correct size.

Part #ML-1101 $19.95 Click on photo for larger view Marshall® TOP VENT, 8 SCREW HOLES - TSL100 HEAD Check the measurement of your existing vent - the MV-211 vent measures 17 5/8' x 3'. Part #MV-211 $9.95 Click on photo for larger view STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall® METRIC Replacements for the standard M6 metric screws used to hold the chassis in virtually every Marshall® head. Washers included. Also used in other British amps, including some Trace Elliot® and Orange® models.

Package of 4 stainless steel screws, with 4 washers. Part #MCB-4 $2.99 (Set of 4 screws w/washers) Click on photo for larger view Marshall® CHASSIS WASHERS - TSL100 Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall® head. Package of 4 washers.

Part #MCW-4 $0.49 (Set of 4 washers) Click on photo for larger view CHASSIS CAGE NUTS, Marshall® M6 METRIC, TSL100 and TSL122 Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall® head. Package of 4 cage nuts. Mates with the MCB-4 screws, above. Part #MCN-4 $4.59 (Set of 4 nuts) Click on photo for larger view Marshall® HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS (SET OF 4) FOR FULL SIZE HEADS. Set of 4 screws, Stainless Steel, 1 1/4' long, Phillips, oval head, with matching cup washers. Fits most all large Marshall® heads, from the JVM and JTM series from the 60s through the JCM-800, JCM-900, JCM-2000 and JVM series.

Ali Mohammad Taji Sharabi Ghazal Mp3 Download. Note: The screw heads in this package have a slight oval shape, as opposed to many Marshall® head back panel screws which have a flat head. This oval shape helps improve the 'bite' of the screwdriver, and helps prevent the screw head from being mangled over time. Part # MBP-4 $1.49 (for a pack of 4 screws and 4 washers). Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass.

The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co. Peavey® is a registered trademark of Peavey® Electronics Corporation. Marshall® is a registered trademark of Marshall® Amplification Plc. Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.

AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies. All company names, logos and product names mentioned on these pages are trademarks of their respective owners. Copyright ©2018 Studio Sound Electronics - All Rights Reserved Not responsible for web site errors or omissions.